Takeoffs, quantities, labor, materials, and pricing — in one workflow. Built for subcontractors, general contractors, and estimators.
ROOM TAKEOFF
Upload
Start with the drawings and project information available for the job.
Analyze
Vega helps identify relevant plan information, dimensions, rooms, assemblies, notes and scope needed for estimating.
Takeoff
Convert plan information into measurable quantities for the trades involved.
Labor & Materials
Turn quantities into the materials and labor tasks needed to build the work.
Pricing
Build the estimate using applicable material, labor and project pricing while keeping costs reviewable.
Review
Review quantities, assumptions and costs before the estimate becomes the basis for a bid.
Vega assists at each stage — review and estimator judgment remain part of the process.
Framing isn't measured like concrete. Concrete isn't measured like flooring. HVAC isn't measured like drywall. Different trades require different measurements and estimating workflows — Vega is built around trade-specific logic rather than one generic calculation.
Framing
Wood framing, blocking, and sheathing quantities.
Concrete & Rebar
Foundations, slabs, and reinforcing schedules.
Excavation
Earthwork, grading, trenching, and site prep.
Drywall
Sheets, framing, tape, mud, and finishing labor.
Flooring
Carpet, hardwood, LVP, and tile takeoffs.
Roofing
Shingles, membrane, underlayment, and flashing.
Mechanical / HVAC
Ductwork, equipment, controls, and system takeoffs.
Plumbing
Pipe runs, fixture counts, and rough-ins.
Trade coverage is expanding. Not every trade is available for every plan type.
A reliable estimate begins with understanding what is actually shown in the construction documents — areas, lengths, counts, rooms, walls, openings, materials, and trade-specific quantities.
ROOM TAKEOFF
Illustrative plan traced from a real permit set. Room areas are as printed on the drawing's schedule.
Illustrative estimating workflow. Pricing is applied through the estimating workflow and remains reviewable.
Estimators should be able to review the quantities and assumptions behind an estimate and make corrections when project conditions require them. Vega shows its work.
Visible quantities
See the rooms, areas, and counts behind each line item.
Editable results
Correct dimensions and quantities directly on the canvas.
Review before bid
Walk the estimate before it becomes the basis for a bid.
Manual correction
Override any value when site conditions differ from the plan.
Illustrative review panel — not an actual Vega estimate.
GENERAL CONTRACTORS
Combine trades into a more consistent estimating workflow — from plan to reviewable estimate — instead of rebuilding each scope from scratch.
SUBCONTRACTORS
Get from plans to trade-specific quantities, labor, materials, and bid preparation — focused on the work you actually perform.
Vega uses AI to assist with understanding construction documents and accelerating portions of the estimating workflow — reading plans, detecting rooms, and building initial takeoffs. It complements estimator review rather than replacing the judgment estimating requires.
Construction estimating software helps contractors turn drawings and project information into takeoffs, quantities, labor, materials, pricing, and an editable estimate. Vega is built around that workflow — from plan to reviewable estimate.
Yes. Upload a plan and Vega reads the floor plan to extract rooms, areas, and dimensions. The results are shown on a canvas where you can review and correct them before they feed into an estimate.
Yes. Vega converts quantities into labor and material costs for the trades involved, using trade-specific calculations. Costs are shown per line item and remain reviewable.
Yes. Quantities and room dimensions are editable on the takeoff canvas, and costs are editable in the estimate. Corrections are saved and used to improve future extractions.
Both. General contractors can bring multiple scopes into one estimating workflow, and subcontractors can focus on trade-specific quantities, labor, materials, and bid preparation. Vega offers plans for each role.
No. Vega assists the estimator by accelerating parts of the workflow — reading plans, building takeoffs, and calculating costs. Review and judgment are still required, and results remain editable.
Vega is built around trade-specific estimating for trades including framing, concrete, drywall, flooring, roofing, HVAC, plumbing, and more. Trade coverage is expanding, and not every trade is available for every plan type.
Upload a plan and see how Vega turns construction information into an estimating workflow you can review, edit, and build from.